This feature is deprecated and you should avoid using it.

A DPOD External Self-Service Console is an instance of DPOD All-In-One installation that is deployed externally to a network, provides users with a Console UI only, and does not store any transactional data of its own. In lieu of storing data, this instance communicates with a DPOD Internal Console.

A typical use for the DPOD External Self-Service Console is to proxy the DPOD Console UI to a less secured network (e.g. a DMZ) without placing DPOD's internal data in that area.

Installation Preparation

Network Requirements

Ensure you have an IP for the DPOD External Self-Service Console (including DNS, default GW, subnet mask and other network configuration).
Ensure you have an NTP server available and obtain the NTP server IP address.
Ensure the ports detailed below are opened during or after install:

From	To	Ports (Defaults)	Protocol	Usage
DPOD External Self-Service Console	NTP Server	123	NTP	Sync time between DPOD instances
DPOD External Self-Service Console	Organizational mail server	25	SMTP	Send reports by email
NTP Server	DPOD External Self-Service Console	123	NTP	Sync time
Users IPs	DPOD External Self-Service Console	80, 443	HTTP/s	Work with DPOD Service Center Console
Admins IPs	DPOD External Self-Service Console	22	TCP	SSH
DPOD External Self-Service Console	DPOD Internal Console	9200, 9302	TCP	Connection to DPOD Internal Console Store

Hardware Requirements

DPOD External Self-Service Console should have a Low load configuration architecture as detailed in Hardware and Software Requirements with the following exceptions:

The Data disk can be as small as 5 GB (instead of 100 GB)
(Optional) You may add a second network interface to separate DPOD's External Self Service Console access to the DPOD Internal Console from the UI interface.

DPOD External Self-Service Console Post Installation Tasks

After installing DPOD on the External Self-Service Console machine, follow the steps below:

Stop DPOD components
Ensure all components are down

Disable some DPOD services:

Edit (using vi) the file /etc/sysconfig/MonTier ,change the following line:

SERVICES_FIRST_GROUP="MonTier-AppAdmin MonTier-Derby MonTier-es-raw-trans-Node-1"

and remove all components except for MonTier-Derby:

SERVICES_FIRST_GROUP="MonTier-AppAdmin MonTier-Derby"

Comment out the following lines:

SERVICES_SECOND_GROUP="MonTier-es-raw-trans-Node ..."
SERVICES_FORTH_GROUP="MonTier-AggAgent- ..."
SERVICES_FIFTH_GROUP="MonTier-BalancerAgent ..."
SERVICES_SIXTH_GROUP="MonTier-WsmAgent-1 ..."

Change DPOD's Store entries in /etc/hosts to direct to DPOD Internal Console IP address (1.1.1.1 in the example below):
```
1.1.1.1     montier-es
1.1.1.1     montier-es-http
```
Start configuration database service
```
start_services.sh -o derby
ij
```

Update the SystemParameter SQL table:

UPDATE SystemParameter
SET value='false'
WHERE name='agents.management.enabled';

UPDATE SystemParameter
SET value='false'
WHERE name = 'system.internal_self_service.is_internal';

UPDATE SystemParameter
SET value='false'
WHERE name = 'system.should_run_retention_on_startup';

update HATSRECURRINGTASK set isEnabled='false' where taskType not in ('DATABASE_CLEANUP', 'FILE_CLEANUP', 'INTERNAL_ALERTS_CHECK_DERBY', 'INTERNAL_ALERTS_CHECK_FS_FREESPACE');

If you wish to let the external self service users access the DevOps Services Portal, change the following system parameters in the external self service console
(you can do that from Manage → Customize → System Parameters after the web console starts):
1. Internal Self Service Address: Enter the address of the internal self service portal.
2. Internal Self Service Webserver Port: (defaults to 443) The webserver port for the internal self service portal - change this value only if advised.
Update external server's encryption key:
1. Copy the encryption key from internal server to the external server's temp folder - do not override servers encryption file:
```
scp root@<internal server ip>:/app/keys/encryption.key /tmp/encryption.key
```
2. Deploy the key using utility:
```
/app/scripts/replace_encryption_key.sh --deploy /tmp/encryption.key
```

DPOD Internal Console Post Installation Tasks

Connect to the DPOD Internal Console server and alter the configuration to let it accept communication from the DPOD External Self-Service Console.

Stop DPOD components
Ensure all components are down :
Change DPOD Store entries in /etc/hosts to bind to DPOD Internal Console IP address instead of 127.0.0.1 (1.1.1.1 in the example below):
```
1.1.1.1     montier-es
1.1.1.1     montier-es-http
```
Start DPOD components

Ensure all components are up and running

app_status.sh

#Output Example:
MonTier-AppAdmin (pid 17836) is running...
MonTier-Derby (pid 17940) is running...
MonTier-es-raw-trans-Node-1 (pid 18125) is running...
MonTier-es-raw-trans-Node-2 (pid 21122) is running...
MonTier-es-raw-trans-Node-3 (pid 21103) is running...
MonTier-es-raw-trans-Node-4 (pid 21120) is running...
MonTier-SyslogAgent-1 (pid 27350) is running...
MonTier-SyslogAgent-2 (pid 27286) is running...
MonTier-SyslogAgent-3 (pid 27177) is running...
MonTier-SyslogAgent-4 (pid 27075) is running...
MonTier-WsmAgent-1 (pid 27002) is running...
MonTier-WsmAgent-2 (pid 26921) is running...
MonTier-WsmAgent-3 (pid 26881) is running...
MonTier-WsmAgent-4 (pid 26773) is running...
MonTier-HK-ESRetention (pid 24012) is running...
MonTier-HK-WdpDeviceResources (pid 27590) is running...
MonTier-HK-WdpServiceResources (pid 27447) is running...
MonTier-HK-SyslogKeepalive (pid 1976) is running...
MonTier-HK-WsmKeepalive (pid 1932) is running...
MonTier-UI (pid 1635) is running...
MonTier-Reports (pid 1830) is running...
MonTier-AgentNode (pid 1736) is running...

Browser not supported