This page describes how DPOD prepares the execution flow of a sync plan (using tasks) and subsequently - how the tasks themselves are executed

Task Creation Flow

General execution flow for a sync plan:

Verify that the system allows Syncs to run. (See Configurable Parameters and Settings to learn how to enable or disable all sync activities)
Verify that the current system time is within the maintenance window timeframe defined for the plan
Iterate over all the activities defined for the plan, and split them into executable tasks.
For example: consider a plan with two activities, one to sync device PROD1 to DR1 and a second to sync domain pattern with source device = PROD1, source domain = Flight* and target device = PROD2
DPOD will create eight tasks:
a. Export task for source device/domain PROD1/Domain1
b. Import task for target device/domain DR1/Domain1
c. Import task for target device/domain DR1/Domain2
d. Import task for target device/domain DR1/Domain3
e. Export task for source device/domain PROD1/Flight1
f. Import task for target device/domain PROD2/Flight1
g. Export task for source device/domain PROD1/Flight2
h. Import task for target device/domain PROD2/Flight2
If all the created tasks are in "Skipped" state (because the devices are not available, or because no devices or domains matched the input patterns) - the plan will stop
If there are any tasks waiting to be executed - the Pre-Plan Script will be executed (if requested in the Backup Plan settings). The plan will stop if the script's return code is larger than 0.

Task Execution Flow

After the sync tasks are created, they will start to execute. The following is the general execution flow for a sync task:

Sync tasks will start to execute in the order they were created, which corresponds to the order which the activities are defined.
Two different tasks will not execute concurrent syncs on the same device, unless the option "Allow multiple sync tasks to run in parallel" was checked in the Sync Plan definition

Verify that the current system time is within the maintenance window timeframe defined for the Backup Plan.
Verify that both source and target devices' firmware levels are above 7.1.0.0
If a deployment policy was specified in the sync activity definition - ensure it exists
If a deployment policy variables object was specified in the sync activity definition - ensure it exists
Check that the source and target device type match (IDG > XB-62 > XI-52 > XG-45) - you can turn this check off in the Sync Activity definition
Check that the source device major firmware level is lower or equal to the target device major firmware level - you can turn this check off in the Sync Activity definition
Check that the target device contains the same licenses/features of the source device (e.g. B2B, SQL-ODBC, Tibco-ESM) - you can turn this check off in the Sync Activity definition
DPOD will try to check if the passphrase in both source and target devices match, and will stop the sync process if they do not.
Export the source domain's configuration
If pre-quiesce was requested - check that the domain is not already quiesced
Run the user's pre-script (if requested in the Sync Activity), the task will stop if the script return value is larger than 0
Issue a Quiesce domain/device SOMA (if requested in the Sync Activity)
Wait for the device or domain to finish quiescing. A timeout value may be specified for the Quiesce SOMA (see Configurable Parameters and Settings),
DPOD will cancel the task if the domain(s) are not yet quiesced 3 minutes after the specified timeout, and will issue an Unquiesce SOMA
Perform an Import Dry-run to try and detect any errors before the actual Import
Delete objects on the target domain (DPOD does not use "reset domain" in order to retain the passwords on the target domains) -
The following object types will be deleted:
1. WSGateway
2. MultiProtocolGateway
3. XMLFirewallService
4. SSLProxyService
5. HTTPService
6. B2BGateway
7. TCPProxyService
8. WebTokenService
9. WebAppFW
10. XSLProxyService
11. CloudGatewayService
12. SQLDataSource
13. MQQMGroup
14. MQQM
15. ISAMReverseProxy
16. TibcoEMSServer
17. LoadBalancerGroup
18. WebSphereJMSServer
Import the configuration into the target domain
Save config on the target domain
Unquiesce the device/domain (if it was previously quiesced by this task)
Wait for the device/domain to unquiesce. A timeout value may be specified for this operation. 3 minutes after the timeout, DPOD will stop waiting for the unquiesce operation and will fail the task (the device's unquiesce operation will not be interrupted though)
Run the user's post-task script (if requested in the Sync Activity)

When all the plan's tasks completed execution, the post-plan script will be executed (if requested in the Backup Plan settings).

Sync Execution Results

The Plan Details page shows the 40 most recent plan execution results

The following table outlines the details for each column in the plan execution table

Column Name	Description
ID	The Plan Execution ID
Start Time	The time the plan entered the execution queue
Devices	Number of devices that were supposed to be synced. Both failed and successful syncs are aggregated.
Domains	Number of domains that were supposed to be synced. Both failed and successful syncs are aggregated.
Status	The current status of the plan
Successful Tasks	Number of sync tasks that completed successfully for this plan execution
Failed Tasks	Number of sync tasks that failed for this plan execution
Skipped Tasks	Number of sync tasks that did not execute, e.g. because the device was not available
Error Message	Plan's Error message (If any)

*Click the red "Abort Pending Executions" to stop execution in status "WAITING_FOR_PRE_VALIDATION" that did not started yet.
**Click the status column to drill into the plan execution details page.

Column Name	Description
ID	The Activity Execution ID
Status Time	The last time the status of the activity changed
Source Device Name	The source device name
Source Domain Pattern	The source domain name or pattern
Target Device Pattern	The target device name or pattern
Target Domain Pattern	The target domain name or pattern
Status	The current status of the activity
Successful Tasks	Number of backup tasks that completed successfully for this activity execution
Failed Tasks	Number of backup tasks that failed for this activity execution
Skipped Tasks	Number of backup tasks that were skipped for this activity execution

Click the status column to drill into the activity execution details page

Column Name	Description
ID	The Task Execution ID
Status Time	The last time the status of the task changed
Source Device Name	The source device name
Source Domain Name	The source domain name
Target Device Name	The target device name
Target Domain Name	The target domain name
Action	EXPORT or IMPORT
Status	The current status of the task
Error Message	Task's Error message if any

Click the status column to drill into the task execution results page, this page will display the Import SOMA result for the task (if an Import was actually performed)

Browser not supported