Page Comparison

DPOD software updates are available from time to time and include enhancements, security updates, component upgrade, bug fixes etc.

The following sections describe the process of upgrading an existing installation. 

To upgrade for v. 1.0.9.0 you must be at version v11.0.8.5.

You should consider performing a full backup.

RPM Prerequisites

Additional RPM packages need to be installed when upgrading a non appliance DPOD installation.
Please make sure the following packages are installed before upgrading: fontconfig

Obtain the software update

DPOD software updates are available through IBM fix central.

...

1. The update file in the format of : DPOD-fixpack-<version number>.sfs (for example: DPOD-fixpack-1_0_9.sfs)
2. The md5 hash calculation of the update file : DPOD-update-<version number>.md5

Copy the software update to the DPOD server

Copy the update files to the following directory on the DPOD server :

...

mkdir -p /installs/update/fix/TODO

Install the software update

Run the following command from the location you downloaded the update files to.

...

MonTierUpdateInstaller.sh -u DPOD-update-1_0_9.sfs -s DPOD-update-1_0_9.md5

Data Migration Tool

The upgrade process checks the existence of Store indices that were created in early versions of the product.
In case that early version indices exist, the upgrade process will stop and notify you of a manual step that you will need to run :

Some of the stored application data cannot be migrated to the latest version of the Store service.

A data migration tool has been deployed in /installs/data-migration-tool.

You may run it using the following command:

/installs/data-migration-tool/data-migration-tool.sh

Further information can be found in the documentation at:

Admin Guide -> Installation and Upgrade -> Upgrade -> Upgrade to v1.0.109.0 - Special Steps

Configuring the Data Migration Tool

You may edit the configuration file /installs/data-migration-tool/data-migration-tool.conf before running the tool, there . There are two entries of interest:

• duration.limit (default: 999999) - limit limits the execution time in minutes, this .
  This option is useful if you want to schedule the tool to run at nightsduring off-peak time. In such a case, you can limit it the tool to run for a few hours each time and schedule it to start when off-peak time starts, so performance will not suffer during normal working be impacted during peak time hours.
• delete.kibana_indices (default: true) -
  "true" determined whether Kibana indices should be deleted or not.
  true - delete old Kibana indices - all exiting Kibana dashboards and other settings will be deleted.
  "false" - keep and migrate Kibana indices to the new store version - Note: Even when migrating the Kibana indices to the new version, the however Kibana version that comes with DPOD 1.0.9 will not be able .0 is unable to read the old indices format, so it is up to you to fix the indices manually according to Kibana's documentation.
• Leave the other settings in data-migration-tool.conf as they are, unless advised otherwise by support.

Running the Data Migration Tool

To run the data - migration - tool manually:

/installs/data-migration-tool/data-migration-tool.sh

Make sure not to interrupt SSH session during the Data-Migration operation.
Alternatively, you can run the tool in a "no hang-up" mode, which will cause the process to continue running even after the SSH session is closed. In this mode, the console output will be written to the nohup.log file in the local directory.

nohup /installs/data-migration-tool/data-migration-tool.sh &

The data migration process may take anywhere between a few minutes and a few days, depending on the amount of data, the server load and the server loadhardware.
A rough estimation of the time left will be calculated and presented on the console output during the process run. These estimations will also be written to the log file.
The estimation is based on current server load, so it may change significantly between peak and quiet off-peak hours.

Please review the Data-Migration data migration tool log file if the console displays any error messagesmessage.
When the Data Migration data migration completes, the console or log file will display the following line message:

Data migration tool finished successfully

Interrupting the Data Migration Tool

Pressing ctrlCtrl+C or setting duration.limit in the configuration file will stop the tool during the migration process.
Stopping the tool will cause it to re-process the last index that was migrated on the next run.

While this is usually not an issue, note that on some cases it may cause complications, for example:
1. The user wants the tool to run during a nightly maintenance window, between 2-4 AM.
2. The tool is scheduled using cron to 2 AM and the duration.limit setting is set to 120 minutes.
3. For this specific user, depending on its hardware and data sizes, processing of each index takes about 3 hours.
4. Since the tool is interrupted after 2 hours, on the next night, the tool will try to migrate the same index again and will never advance to the next index.

Resuming Software Update

To proceed with the software update, you can rerun the software update command:

...

Please review the upgrade log file if the console displays any error messages.

Update Store Allocation

Open the DPOD admin console on your favorite browser:

...

Admin Console -> Utilities -> Store -> Store Allocation

Run the update_store_allocation process Update Store Allocation utility:

Confirm the operation  :

...