...
Note: You may choose between extending the existing data disk (option 1), or adding additional disks (option 2).
Since DPOD uses fdisk utility for creating partitions in the data disk during installation, it only supports extending the existing data disk (option 1) up to 2TB. However, additional disks (option 2) can be larger than 2TB.
Option 1: Extending the Existing Data Disk
Extending the Disk in a Physical Server
For physical servers, use the server vendor's RAID management software to extend the existing RAID Disk (LUN) in order to increase the data disk.
Extending the Disk in a Virtual Machine
Use the VMware vSphere Client in order to edit the DPOD virtual machine settings:
- Stop the DPOD virtual machine.
- Select Edit virtual machine settings
- Select the 3rd hard drive (which is the data disk, as described in the Hardware and Software Requirements page).
- Increase the Provisioned size of the hard drive and press OK.
- Wait for the increase process to finish.
- Start the DPOD virtual machine.
Configuring the File System after Extending the Disk
Verify the current size of mount point /data:
Code Block language bash theme RDark df -h /data
The system output should resemble the following:
Verify the new disk size:
Code Block language bash theme RDark fdisk -l | grep /dev/sdc
The system output should resemble the following:
Use fdisk to create a new partition for the new size:
Code Block language bash theme RDark fdisk /dev/sdc
- Press p to print the partition table to identify the number of partitions:
If this is the first time the disk is extended, you should only see sdc1. If this is a subsequent extension - you will see additional sdcX listed (e.g. sdc2 for the second extension). - Press n to create a new primary partition.
- Press p for primary.
- When the system prompts for a partition number, enter the next number depending on the output of the partition table print.
If this is the first extension and you see only one row of output - enter 2. If this is the second disk extension then the partition number will be 3, and so on. - Press Enter twice
- Press t to change the system's partition ID.
- Press 2 to select the newly created partition (Remember: if this is a subsequent disk extension - the number will be 3 or higher).
- Type 8e to change the Hex Code of the partition for Linux LVM.
Press w to write the changes to the partition table.
Note The following warning is valid, the system reboot will fix the issue:
“WARNING: Re-reading the partition table failed with error 16: Device or resource busy. The kernel still uses the old table. The new table will be used at the next reboot or after you run partprobe(8) or kpartx(8)”
- Press p to print the partition table to identify the number of partitions:
Reboot the system:
Code Block language bash theme RDark reboot
When the system is available again, ensure the new partition is available:
Code Block language bash theme RDark fdisk -l | grep /dev/sdc
The system output should resemble the following (note the new sdcX added):
- Stop the application by running app-util.sh and selecting option 2 (stop allStop all services using Command Line Interface (CLI) (Option 2 - Stop All).
Configure the new partition:
Note If the new partition is not sdc2, substitute sdc2 for the right qualifier in all the following commands
Code Block language bash theme RDark pvcreate /dev/sdc2 vgextend vg_data /dev/sdc2 lvextend -l +100%FREE /dev/vg_data/lv_data
Identify the /data file system type (for CentOS 7.2+ based appliances the type is xfs):
Code Block language bash theme RDark cat /etc/fstab | grep /data
The system output should resemble the following:
Resize the file system. Select the correct command below for your file system type:
Code Block language bash theme RDark title For ext4 resize2fs /dev/vg_data/lv_data
Code Block language bash theme RDark title For xfs xfs_growfs /dev/vg_data/lv_data
The system output should resemble the following:
Display the new size of the /data mount point:
Code Block language bash theme RDark df -h /data
Update the Store configuration file
(see below:
Code Block language bash theme RDark /app/scripts/update_store_allocation.sh -l 4
- Start all services using Command Line Interface (CLI) (Option 1 - Start All).
Option 2: Adding an Additional Data Disk
Adding an Additional Disk in a Physical Server
For physical servers, use the server vendor's RAID management software to add new RAID Disk (new LUN), in order to increase the data disk.
Adding an Additional Disk in a Virtual Machine
Use the VMware vSphere Client in order to edit the DPOD virtual machine settings:
- Stop the DPOD virtual machine.
- Select Edit virtual machine settings
- Select Add > Hard Drive
- Ensure to configure the new hard drive as Thick Provision Eager Zeroed
- Wait for the increase process to finish.
- Start the DPOD virtual machine.
Configuring the File System after Adding the Disk
Verify the current size of the /data mount point:
Code Block language bash theme RDark df -h /data
The system output should resemble the following:
Identify the new disk:
Code Block language bash theme RDark lsblk [ Note: Example output below is filtered to show only sdd disk information, but should include many more entries of sda, sdb and sdc disks ] NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT sdd 8:32 0 200G 0 disk
Stop the application by running app-util.sh and selecting option 2 (stop all)Stop all services by using Command Line Interface (CLI) (Option 2 - Stop All).
Execute the following commands. Replace the name of data disk if it is different in your environment.
Code Block language bash theme RDark pvcreate -ff /dev/sdd vgextend vg_data /dev/sdd lvextend -l +100%FREE /dev/vg_data/lv_data
Identify the /data file system type (for CentOS 7.2+ based appliances the type is xfs):
Code Block language bash theme RDark cat /etc/fstab | grep /data
The system output should resemble the following:
Resize the file system. Select the correct command below for your file system type:
Code Block language bash theme RDark title For ext4 resize2fs /dev/vg_data/lv_data
Code Block language bash theme RDark title For xfs xfs_growfs /dev/vg_data/lv_data
The system output should resemble the following:Display the new size of the /data mount point:
Code Block language bash theme RDark df -h /data
The system output should resemble the following:
Execute the following script to update the Store configuration file with the new file system sizeUpdate the Store configuration file
(see below).
Update the Store Configuration File
:
Code Block language bash theme RDark /app/scripts/update_store_allocation.sh -l
1Start the application by running app-util.sh and selecting option 1 (start all4
- Start all services using Command Line Interface (CLI) (Option 1 - Start All).