DPOD can be configured with two network interfaces:

...

Use your system administrator assistance to add a second network interface to your virtual machine or physical server.

In some cases, there will be a need to restart the server before the new network will be available.

...

Create a New Routing Rule

The routing rule instructs the operating system when to use the new routing table.

1. In order to add a new routing rule entry to the new routing table use the "ip rule" command.
   This command will add a new temporary rule entry.

   Code Block
   ip rule add from <source ip address or subnet> table <routing table name> ip rule add to <destination ip address or subnet> table <routing table name>

   
   For example: The routing rule for monitored device 192.168.1.120 are :are 

   Code Block
   language bash theme RDark
   ip rule add from 192.168.1.120/32 table rt1 ip rule add to 192.168.1.120/32 table rt1

   The specific IP address can be replaced with subnet if subnet rule is appropriate: 192.168.1.0/24
   
   

2. In order to make these entries permanent edit the file /etc/sysconfig/network-scripts/rule-<interface name> and add the following:
   
   

   Code Block
   from <source ip address or subnet> table <routing table name> to <destination ip address or subnet> table <routing table name>

   For example: The routing rule for monitored device 192.168.1.120 are :
   
   

   Code Block
   from 192.168.1.120/32 table rt1 to 192.168.1.120/32 table rt1

   
   

3. To confirm that the new routing rules entries added use the following command to display them:
   
   

   Code Block
   language bash theme RDark
   ip rule show The output should include the following lines: 32764: from all to 192.168.1.120 lookup rt1 32765: from 192.168.1.120 lookup rt1

   
   

...

1. Restart the server.
2. After the server is up again login via SSH.
   Use the "ip route show tab" command and the "ip rule show" command make sure the routing entries and the routing rule persists after the restart.

3. Confirm the needed network connectivity to the monitored device:
   Open new CLI session via SSH and start capture network traffic passing through eth1 to the wanted monitored device.
   The following command will capture network traffic to 192.168.1.120:
   
   

   Code Block
   language bash theme RDark
   tcpdump -i eth1 host 192.168.1.120

   
   On the second SSH session run telnet command to test connectivity to the monitored device using port 5550 (XML Management Interface Port):
   
   

   Code Block
   language bash theme RDark
   telnet 192.168.1.120 5550

   The output of the tcpdump command should look similar to the following:
   The source of the tcp connection is the new eth1 ip address and the destination is the monitored device ip address:
   
   

Configure DPOD

...

for the New Network Interface

After the new network interface is configure correctly we need configured correctly, DPOD configuration needs to change DPOD configuration to use the new interface.

Change DPOD

...

Configuration

1. Edit the file /etc/hosts and alter the following entries to point to the new ip IP address :.
   In this example we changed For example, these are the entries to for the new ip IP address 192.168.1.178:
   
   

   Code Block
   192.168.1.178 montier-syslog 192.168.1.178 montier-wsm

   
   

2. Restart the application using the CLI Admin Menu.

Re

...

-configure Syslog and WS-M

After DPOD was configured to use the new ip address we IP address, the monitored devices need to be re-configure the monitored devices configured to communicate with DPOD via the new address.

In order to re-configure the monitored devices, please follow the instructions on the following item  under "Adding Monitored Devices" - sub items "Setup Syslog For The for the New Monitored Device" and "WS-M setup for device"   .