Before You Begin

Before you begin adding new monitored devices to DPOD, you can may backup the objects that the DPOD will alter during the configuration phase. objejct like , such as the XML management interface, the WS-M agent etc.,
For detailed information regarding IDG DPOD related objects backup and restore see : Backing up and Restoring DPODs IDG related configuration

Before you can add a new monitored device to DPOD, ensure to perform the following:

1. Check routing and access from a monitored device:
   The DataPower Gateway needs to route packets to DPOD Agents through the desired interface. Validate through the DataPower's [control panel->Troubleshooting->TCP Connection Test]
2. Log In To -in to DPOD Web Console

Device Level Configuration

Add The Device In DPOD

...

1.  Inside DPOD's Web Console, navigate to Monitored Devices  [Manage->Devices->Monitored Devices] and click on “Add Device”
2. Enter the information required. (Consult Device Management for details)
   Note that the device name must be identical to the System Identifier/Appliance Name of the DataPower Gateway as set in the IDG itself, and must meet the requirements detailed in http://www-01.ibm.com/support/docview.wss?uid=swg21668456.
   
   
   
   
3. Click “Add”
4. DPOD will add the device. (Verify by locating the new device in the list of monitored devices)

Configure The New Monitored Device

1. On Inside DPOD's Web Console, navigate to the devices list page [Manage->Devices->Monitored Devices]
2. Click the name of the device you added in the previous step
3. Click "Setup” and wait for an informative green message at the top does s this do? how is this now 'configured'? are the following sections 'inside'?

...

1. Under "Syslog Setup for Device", select the correct Syslog Agent according to the architecture design, click "Setup Syslog for device" and wait until the action completes successfully.
   Image RemovedImage Added 

Syslog setup for all domains

1. Under "Syslog Setup for All Domains", select the correct Syslog Agent according to the architecture design, click "Setup Syslog for all domains" and wait until the action completes successfully.

...

Image Added 
diagram to new-name

...

Auto Setup Domains (Optional)

• Under "WS-M Setup for Device", click "Setup WS-M for all domains" and wait until the action completes successfully.
• Note: You may elect to only enable WS-M for specific domains. If this is the case, setup each domain separately as documented below.

Image Removed

...

This feature will automatically detect and setup new domains created on the monitored device. This is especially useful for dynamically created API Connect domains.
Select a Syslog agent that the domains should report to, enter the domain pattern (use asterisk as wildcard) and click save.
DPOD will scan the monitored devices every 2 minutes and will setup the new domain. You may change the scan interval on the system parameters page. (A UI service restart is required after changing this interval)

Image Added

Domains WS-M Setup (Optional)

Under "Domains WS-M Subscriptions for All DomainsSetup", select the correct WS-M Agent according to the architecture design, click "Subscribe to . Click "Setup WS-M for all domains” M” and wait until the action completes successfully.A WS-M subscription will be created for each domain where one is not already created by DPOD.
For supported WS-M payload capture services see IDG WS-M payload capture support

Consult System Parameters List for information regarding the time interval parameter.

 .
Click on "Record Payload" to open the payload capture page where you can start capturing payloads

Image Added

Extended Transaction setup (Optional)

...

Image RemovedImage Added

Certificate Monitor (Optional)

Under "Certificate Monitor", click "Setup Certificate Monitor for Device” and wait until the action completes successfully.
Consult Consult the System Parameters List for information regarding the time interval parameter.Image Removed

Image Added

Domain Level Configuration

Configuring a specific domain (Optional)

1. Navigate to the domain setup page  [Manage→ Devices→ Monitored Devices]
2. Click the device name of the device
3. Click the domain name of the domain
4. Click "Setup”
    

Syslog setup (Optional)

Under "Syslog Setup", select the correct Syslog Agent according to the architecture design, click "Setup Syslog" and wait until the action completes successfully.

WS-M setup (Optional)

Under "WS-M Setup", click "Setup WS-M" and wait until the action completes successfully.

WS-M Subscription (Optional)

Under "WS-M Subscription", select the Select the correct WS-M Agent according to the architecture design, click "Subscribe to . Click "Setup WS-M” and wait until the action completes successfully.Only one subscription from DPOD can be enabled per domain at a time.
For supported WS-M payload capture services see see IDG WS-M payload capture support

...

.
Click on "Record Payload" to open the payload capture page where you can start capturing payloads

Extended Transaction setup for all services (Optional)

Under "Extended Transaction Setup for All Services", click "Setup Extended Transaction for all services” and wait until the action completes successfully.

...