Versions Compared

Old Version 69

changes.mady.by.user Hanan Kenan

Saved on

compared with

New Version 70

changes.mady.by.user Assaf Cohen

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

The features listed below were added to DPOD. The following conventions are used in this document:

(red star) - Some actions are required to enable the feature.
(thumbs up) - This is a Tech Preview Feature. Consult the release notes for more information. 

New Features 1.0.7

...

Tenant

...

Support 

...

  • Added the ability to monitor transactions information on appliance with Tenants (Resource monitoring and appliance maintenance are not supported available for tenants).

API Connect Integration

  • New API Connect Recent Activity dashboard - The dashboard shows  ???shows high level overview of APIs activity.
  • The Early Failed Dashboard in now also visible in API Connect view
  • Enable filtering transactions by OAuth Token valid from and to time range

Feature Improvements

  • Add an indication in the transaction page showing whether a DataPower probe was open when the transaction run
  • Allow to start payload capture on multiple devices or domains at once
  • REST API - New Reports REST API, Add REST API call to show all available APIs (Reports, Alerts and Appliance Maintenance)
  • Filters - New URI filter in the Service URL Calls page, Add a Free Text filter to the Logical Transactions Page.
  • Alerts can be tested against some of APIs execution data.
  • Auto Setup Domains - improve detection when a domain was reset and auto-setup it again.

Maintenance Plans improvments 

  • DPOD now provides the ability to upgrade virtual and physical appliance firmware (requires firmware 7.5+) - see limitations

  • Maintenance Plan for Syncing DataPower Appliance Configuration is now supported (initially announced as tech preview from v1.0.5)

Improved User Experience

  • Improvement in error analysis indicating a probe is enabled.
  • New alerts on latencies based on percentile.
  • Add latency percentiles to Service URL calls and Service URI calls pages, add a button to create alerts on transactions above a certain latency.
  • Payload capture can be enabled on multiple devices or domains at once.

  • DevOps Services Portal - allow to setup a separate temporary domain (for WSDL validation and promotion) for each device

  • Auto Setup Domains - try to detect when a domain was reset and auto-setup it again

Improved User Experience

  • Admins can now decide which columns to show or hide

    .

  • Columns can be hidden or reordered in the Transactions, Raw Messages and API Connect Transactions pages
  • Message code column was added to the Raw Messages page
  • Add a wizard to generate common schedule expressions for scheduled Reports, Alerts and Appliance Maintenance Plans
  • Fix screen layout issues for lower screen resolutions and mobile devices
  • Add paging to security dashboards
  • Reports page new look and feel

Internal Monitoring

  • New Dashboard showing internal monitoring and status of DPOD's components, admins will get a notification when an internal alert is generated
  • Show warning in the agent page when a monitored device's time is later than DPOD's agent time
  • Show a message to admin users with current store status and earliest indexed syslog document

Maintenance Plan for Upgrading Appliance Firmware

  • DPOD now provides the ability to upgrade virtual and physical appliance firmwares (requires firmware 7.5+).
  • Internal Monitoring new page that shows DPOD's components status and alerts to assist monitoring DPOD health.

New Features 1.0.6

DevOps Services Portal 

...

  • Users can now save favorite filter combinations and use them in subsequent sessions.

  • A new free text search field was added to the Transactions List page and Raw Messages Page where the user may enter a single value that will be searched across various data fields.
  • Service filter now supports auto completion.
  • All applicable filters support multi-select of values.
  • Users can now change the size of the series (number of values) that is displayed in charts of type "top N".
  • A recent notifications panel was added to The Navigation Bar. It displays the recent UI notifications for the user (not persisted).
  • A new "Share" button added. It allows sharing the current page (including filters, transaction ID etc.) by copying/pasting the current URL or by sending it via email
  • Time range filters now provides more options: last 10 minutes, start of day, start of week, this month.
  • Consistent behavior across pages of zoom into a transaction or use its value as a filter criteria.

...

  • From time to time, DPOD customers may be required to install a new DPOD installation while preserving the data already collected. for example:
    • Customer deployed DPOD Appliance mode at version v1.0.0 with CentOS 6.7 and now requires to migrate to CentOS 7.2 introduced at version v1.0.2+.
    • Customer deployed DPOD on a virtual server but load increased and now requires a physical server.
    • Customer deployed DPOD Appliance mode but wants to migrate to Non-Appliance mode (RHEL) to better comply with their organization security requirements and standards.
  • New procedure and tools were introduced to support customers with migration of an existing DPOD Store data to a new DPOD installation in each of the scenarios above.

New Features 1.0.5

API Connect Integration

...

Maintenance Plan for Syncing DataPower Appliance Configuration ((thumbs up)) - see limitations

DPOD now provides a multitude of syncing capabilities:

...

  • A monitored device may now be attached to several DPOD installations.

  • Naming each DPOD installation and reflection of this.

  • Node naming and configuration editing from the UI.
    (red star) During installation / upgrade you will need to set the system variables.

Feature Improvements

  • New alert for transaction errors

  • New report: export basic monitored device service configuration

  • Improved High Availability Scenarios 

    • A limited Active / Active scenario is now supported if the same monitored device is connected to two separate and independent DPOD installations

    • New REST APIs introduced, to support Active / Standby scenario

  • New filter to search logs by B2B message id or B2B partner id

  • Improved error Analysis by providing simple human readable errors that are most common in:

    • SSL scenarios within a transaction
    • Side calls scenarios within a transaction (when the Side Call feature is enabled)
    • API Connect scenarios within a transaction (when the API-C feature is enabled)

...