Before You Begin
Before adding new monitored devices to DPOD, you may backup the objects that the DPOD will alter during the configuration phase, such as the XML management interface, the WS-M agent etc.
For detailed information regarding IDG DPOD related objects backup and restore see : Backing up and Restoring DPODs IDG related configuration
...
- Inside DPOD's Web Console, navigate to Monitored Devices [Manage->Devices->Monitored Devices] and click on “Add Device”
Enter the required information required. (Consult Device Management for details)
Note that the device name must be identical to the System Identifier/Appliance Name of the DataPower Gateway as set in the IDG itself, and must meet the requirements detailed in http://www-01.ibm.com/support/docview.wss?uid=swg21668456.Info If you wish to add a Tenant device, enter the landlord's name but use the tenant's SOMA port, DPOD will display the tenant's name as tenant@landlord
- Click “Add”
- DPOD will add the device. (Verify by locating the new device in the list of monitored devices)
...
Configure The New Monitored Device
...
Right after adding the device, the "Setup" tab will be displayed, the tab is divided into six parts:
wing sections 'inside'?
...
- Device
...
- Under "Syslog Setup for Device", Syslog Agent - select the correct desired Syslog Agent according to the architecture design, click "Setup Syslog for device" and wait until the action completes successfully.
Syslog setup for all domains
- Under "Syslog Setup for All Domains", select the correct Syslog Agent
Setup Syslog for All Domains -
Tip This section will apply the same setup too all domains in the device, to select a different configuration for each domain, see the section "Domain Level Configuration" later on this page.
select the desired Analysis Level, select the Syslog agent according to the architecture design
,and click "Setup Syslog
for all domains" and wait until the action completes successfully.
diagram to new-name
...
| title | Performance |
|---|
...
", the operation may take a few minutes
- Auto Setup Domains (Optional) -
This feature will automatically detect and setup new domains created on the monitored device. This is especially useful for dynamically created API Connect domains.
Select a Syslog agent that the domains should report to, enter the domain pattern (use asterisk as wildcard) and click save.
DPOD will scan the monitored devices every 2 minutes and will setup the new domain. You may change the scan interval on the system parameters page. (A UI service restart via the CLI is required after changing this interval)
For domains that match the auto setup pattern - DPOD will also try to detect if any domain was reset and setup it again.
...
Domains WS-M Setup (Optional)
...
Tip This section will apply the same setup too all domains in the device, to select a different configuration for each domain, see the section "Domain Level Configuration" later on this page.
If you wish to record and view payloads, select the desired WS-M Agent according to the architecture design
...
and click "Setup WS-M”
...
, the operation may take a few minutes.
For supported WS-M payload capture services see IDG WS-M payload capture support.
Click on "Record Payload" to open the payload capture page where you can start capturing payloads
...
- Certificate Monitor Setup (Optional)
Under "Extended Transaction Setup", click "Setup Extended Transaction for Device” and wait until the action completes successfully.
- If you wish to use DPOD's expired certificate dashboard, click on "Setup Certificate Monitor"
Consult the System Parameters List ("Certificate monitoring duration in days") for information regarding the time interval parameter. - Extended Transaction Setup (Optional, Deprecated)
| Warning |
|---|
This step will MODIFY SERVICES PROCESSING POLICY. You must test and verify that the services are not affected by this change before setting this up on production environments. |
...
This feature
...
Certificate Monitor (Optional)
Under "Certificate Monitor", click "Setup Certificate Monitor for Device” and wait until the action completes successfully.
Consult the System Parameters List for information regarding the time interval parameter.
...
is deprecated and was replaced by a non-intrusive method.
Please do not use the button unless advised by L2/L3 support.
Domain Level Configuration
...